USA

USA Dedicated VPN
Unlimited Bandwidth
USA & CANADA
$7/month  DETAILS

  europe

6 IPs locations Dedicated VPN
Unlimited Bandwidth
UK,France,Germany
Spain,Switaerland,Netherlands  DETAILS

   UK

London Dedicated VPN Unlimited Bandwidth
UK/LONDON
$8 /month  dETAILS

   australia

  • Australia Dedicated VPN
  • Unlimited Bandwidth
  • Sydney
  • $10/month
DETAILS

Error VPN & Troubleshoot

 

 

Troubleshoot & Error number


Error 619:

Solution:
Error 619: 1. The port was disconnected (or Error 645, Dial-Up Networking could not complete the connection to the server and Error 930, The authentication server did not respond to authentication requests in a timely fashion. The Event Viewer shows: Event id: 20073, Description: The following error occurred in the Point to Point Protocol module on port: port number, UserName: user name. The authentication server did not respond to authentication requests in a timely fashion). When using VPN to access a remote network, W2K clients mat get above errors but not win9x and ME clients. This issue occurs because the VPN server hasn't registered in Active Directory.
2.You get this message when connecting via cable modems, dial up DOESN'T have any issues.

Resolution: 1) This problem most likely is secure issue such as unsecured password. So, check the settings.
2) It could be the hardware issue. Try to re-setup the device or download the new driver or just reset the devices such as modem and router.
3) Reapply the service pack
4) If the RRAS is in a domain network, add the VPN to the appropriate group. To do this, go to Active Directory Users and Computers>domain name>Users, double-click the RAS and IAS Servers security group. Select the members and add the VPN server to this group. 2) Type netsh ras add registeredserver at a command prompt (registeredserver is vpn server name), and then press ENTER.
5) If the router is connectijg to a modem and setup DHCP to receive IP from the modem, you may try to assign static IP to the WAN port on the router.


Error 628:
The port is disconnected or The connection was terminated by the remote computer before it could be completed. This is most likely a modem or phone line noise issue or blocking port issue.

Solution:
1) make sure you have good phone line.
2) Upgrade the modem/router firmware.
3) Make sure you logon using the correct username or password or try different username.
4) Reinstall the modem.
5) Check the router/firewall settings.
6) Make sure the router is VPN pass through or GRE is enabled.
 


Error 629 - The port was disconnected by the remote machine (also re: error 913).

Solution:
1) Make sure the username and password you have entered for the DUNS connection is correct.
2) Also make sure the phone number is correct.
3) if calling a server set for 128-bit encryption when you don't have 128-bit encryption installed on client.
4) if all the entries for RAS are not correct, you may get this error. This would include incorrect settings for the Basic, Server, Script, Security and X.25.
5) The settings for authentication and encryption on the security tab must match what your ISP requires.
6) if a new account logs on using PPTP and change password on first logon is enabled.
7) may be caused if the modem port speed is set below 19,200.
8) Can be caused by software or modem not being configured properly or being damaged.


Error 630:
The port was disconnected due to hardware failure.

Solution:
1) Check that the modem is plugged in, and if necessary, turn the modem off, and then turn it back on.
2) Check if your modem is being given a bad init string - with a command that it does not support.
3) Check if another program is already using the modem, or, if the modem or serial port's resources configuration is incorrect.
4) Reboot your computer and try it again.
5) If that doesn't work, go to Start -> Settings -> Control Panel -> Modems -> Diagnostics and get More Info from your modem. If it fails, your modem driver is corrupt and needs to be re-installed.
6) Update the modem drivers.


Error 633:
Modem is already in use, or is not configured for Remote Access dial out or The port is in use.

Solution:
1) Verify no other applications that are using the modem. You can open Task Manager to check that by press CTRL+ALT+DEL. Another way to test it is reboot the computer.
2) This behavior may occur when another device with a driver, for example outdated Palm Pilot software, conflicts with the modem.
3) Telephone.ini or unimdm.tsp is missing or damaged.
4) Make sure the modem is setup correctly and may apply SP.
5) Removing and reinstalling it, or apply the new drive may fix the problem.
6) Make sure no two ISDN installed on the same machine and attempt to connect to the same server.


Error 638:
Remote PPP peer or computer is not responding.

Solution:
If you have tried many thing other people suggest like rebooting, reloading hardware and re-installing the VPN or dial in connection, you still get the same problem. I will suggest to check the router settings and make sure TCP Port 1723, IP Protocol 47 (GRE) are opened. Also make sure that the router has the PPTP enabled and not firewall block the traffic. On the RAS server, check the DHCP settings.


Error 645:
Internal authentication error (also re: error 913), or Dial-Up Networking could not complete the connection to the server.

Solution:
1) Make sure you are entering your correct username and password when connecting.
2) Uninstall and reinstall the Dial Up adapter.


Error 678:
There was not answer.

Solution:
1) Make sure you have good connection.
2) If using VPN, make sure the port 1723 and IP Protocol 47 (GRE) are opened.


Error 691:
Access denied because username and/or password is invalid on the domain.

Solution:
1) Verify the logon ID and password are correct.
2) Turn off your windows firewall (Control Panel>Windows Firewall)
3) Check your Antivirus firewall, it should be allowed to VPN software.


Error 721:
Remote PPP peer or computer is not responding.

Solution:
Switch from PPTP to L2TP.
Resolution: If you have tried many thing other people suggest like rebooting, reloading hardware and re-installing the VPN or dial in connection, you still get the same problem. I will suggest to check the router settings and make sure TCP Port 1723, IP Protocol 47 (GRE) are opened. Also make sure that the router has the PPTP enabled and not firewall block the traffic. On the RAS server, check the DHCP settings.

Error 732:
The PPP negotiation is not converging.

Solution:
Make sure you have good connection.

Error 741 - 789:
The local computer does not support the required encryption type.

Solution:
1) Make sure you enter correct password.
2) Check that you selected IPSec VPN in connection setting and your preshared-key is correct (for manual connection in L2TP).
3) Switch from L2TP to PPTP.

Error 768

The connection attempt failed because of failure to encrypt data

Cause: the VPN server doesn’t setup to use encryption.

Solutions:

1. Setup encryption on the VPN server.

2. If encryption is not necessary, disable encryption on the VPN client and try again.


Error 769
Error Why is Windows VPN reporting error 769 when trying to connect to MacConnect?
This error may occur when attempting to connect to the Internet via a PPPoE (Point-To-Point Protocol over Ethernet) connection, a connection type often used with DSL (Digital Subscriber Line) Internet connections, as a result of a disabled network card.

From the Desktop, right-click My Computer and choose Properties.
Click the Hardware tab and click the Device Manager button.
Once the list populates, use the plus sign (+) beside Network Adapters to expand that branch of the navigation tree.
Find your network card, which will probably have a yellow exclamation mark beside it. Double-click the network card and choose Use This Device (Enable) from the Device Usage drop-down list.
Click OK, close the Device Manager, and try your PPPoE connection again.

Error 792:
The L2TP Connection Attempt failed because security negotiation timed out.

Solution:
1) Check that you selected IPSec VPN in connection setting and your preshared-key is correct.
2) Switch from L2TP to PPTP.

Error 797
The modem could not be found.

Resolutions:
1. Rebooting the machine that may solve the problem.
2. Remove and then re-install the modem.
3. Check to see if there is an upgrade driver for your modem.


Error 800:
Unable to establish the VPN connection. The VPN server may be un-reachable, or security parameters may not be configured properly for this connection.

Solution:
1) if you have firewall, open TCP Port 1723, IP Protocol 47 (GRE).
2) make sure you can reach the VPN server by using ping. Sometimes, poor connection can cause this issue too.
3) You may need to updated firmware on a router or firewall if other OS (win9x/nt/me/w2k) works except XP.
4) The VPN server may not be able to get IP from DHCP for the VPN client. So, you may want to re-configure VPN host networking settings. For XP pro VPN host, go to the Properties of the VPN>Network, check Specify TCP/IP address and Allow calling computer to specify its own IP address, and uncheck Assign TCP/IP addresses automatically using DHCP.
5) Make sure no other secure software blocks your access, for example, if you use Norton secure software, you may need to add the remote client's IP so that the client can access.
6) If your VPN running on a Windows RRAS with NAT enabled, you may want to check the NAT settings.
7) If you can establish the VPN from the desktop at home but not from the laptop. Make sure no security software like Microsoft OneCare software that blocks the GRE.


Error 806:
A connection between your computer and the VPN server has been established but the VPN connection cannot be completed. The most common cause for this is that there is at least one internet device between your computer and the VPN server is not configured to allow GRE protocol packets Verify that protocol 47 GRE is allowed on all personal firewall devices or routers. if the problem persists, contact your administrator.

Solution:
*) Make sure you can reach the VPN server by using ping. Sometimes, poor connection can cause this issue too.
**) Make sure other secure software blocks your access, for example, if you use Norton secure software, you may need to add the remote client's IP so that the client can access.
1) if you have a router/firewall, make sure you open TCP Port 1723, IP Protocol 47 (GRE).
2) make sure you can reach the VPN server by using ping. Sometimes, poor connection can cause this issue too.
3) You may need to updated firmware on a router or firewall.
4) The VPN server may not be able to get IP from DHCP for the VPN client. So, you may want to re-configure VPN host networking settings. For XP pro VPN host, go to the Properties of the VPN>Network, check Specify TCP/IP address and Allow calling computer to specify its own IP address, and uncheck Assign TCP/IP addresses automatically using DHCP.
5) Make sure other secure software blocks your access, for example, if you use Norton secure software, you may need to add the remote client's IP so that the client can access.
6) If your VPN running on a Windows RRAS with NAT enabled, you may want to check the NAT settings.


To configure router dlink dir600 :
1st you have to connect through cable one of ports of your router ( dir600 ) to your computer
2nd type in internet explorer: 192.168.0.1
it shows admin page with user and password
enter username as : admin
password: keep it empty
press enter
and continue to go to configuration
after that you will go to pptp or l2tp connections


Vista with Live OneCare Installed - Could Block VPN:
Windows Live OneCare replaces the existing built-in firewall and although applications are enabled by default for communication, certain required ports aren't. Thus, when you attempt to create a VPN connection to a network, the process will appear to hang, then fail, at the username and password authentication stage. To resolve the problem, perform these steps:

Solution:
1) Start the Windows Live OneCare console (right-click the OneCare taskbar icon, which is normally a green circle with 1 in it, and select "Open Windows Live OneCare").
2) On the left side of the OneCare dialog box under Other Tasks, click the "View or change settings" link.
3) On the "Windows Live OneCare Settings" dialog box, select the Firewall tab.
4) Click the "Advanced settings" button.
5) Select the "Ports and Protocols" tab on the "Advanced settings" dialog box.
6) Select the "VPN - General Routing Encapsulation (GRE)" check box.
7) Click OK to all open dialog boxes.


Mcafee Plus Internet Security - Could Block VPN:

Solution:
1) Begin by opening the mcafee security center by right clicking on the Mcafee icon near the system tray (the clock in the lower right of the screen.) You will need to click on "Advanced Menu".
2) Next, on the left panel of Mcafee Security Center. Click "Configure", then "Internet & Network". Afterwards, click the "Advanced" button.
3) Next, on the left hand side of the window, select "Trusted and Banned IPs & Click Add".
4) Add a single IP address, th server IP address. In the description field, you can add any description you would like to describe the connection. When you are done, click the OK button. After closing the Security Center, you should now be able to connect to the VPN.


Norton Internet Security - Could Block VPN:

Solution:
1) Begin by opening the Norton program window by double clicking on the icon in your system tray (in the lower left of your screen near your clock). Next, you will need to click on "Options" and then "Norton Internet Security".
2) Next, click on "Personal Firewall" and "Trust Control" and then click on the "Trusted" tab. Click the "Add" button.
3) Add the IP address for the VPN server. Next, Click the Ok button.
4) Finally, click the OK button to apply the settings. After closing the Security Center, you should now be able to connect to the VPN.

 

 

Tags:  Error VPN & Troubleshoot | Error number , numbers of error , Buy VPN ,buy vpn with lr , sale vpn, USA VPN, USA IP, Ohio VPN, Texas VPN, New York VPN, Chicago VPN, California VPN, cheap vpn, UK VPN, Canada VPN, cheap VPN, fast vpn, secure vpn, USA IP, UK IP, free IP, IP for skype, test vpn, order vpn , CA IP , sale , vpn , dedicated IP ,IP, VPN, Dedicated IP, Valid IP from USA, United Kingdom, England, Netherlands IP, Holland VPN, Netherlands VPN, Holland IP, VPN Holland, California VPN, California IP, Chicago VPN,New York VPN, Chicago IP, Canada IP, Canadian IP, Canada VPN, UK IP, UK VPN, Texas VPN, Ohio IP, Change Your IP, Personal IP, American IP , australia VPN, Holand Dedicated IP , www.NoodleVPN.com , personal vpn , buy vpn , buy vpn usa ,buy a vpn ,buy vpn ip, buy vpn, buy vpn LR, buy vpn uk, personal IP, dedicated IP , congif dlink dir 600 , set router